Overview
Designed specifically for fitness equipment, these units-commonly called gas springs, gas struts, lift supports, gas shocks, or gas props-balance panel weight and control motion on console hoods, shrouds, and access lids. Land engineers each assembly for consistent force, quiet operation, and long service life through thousands of club-use cycles.
Key Features
Controlled motion: tuned oil damping for soft open and soft close on plastic or metal covers.
Size range: extended lengths 8–22 inch with typical strokes 60–200 mm to suit compact consoles and deep shrouds.
Force options: factory-set 120–550 N (approx 27–124 lbf); adjustable-force options available for precise balance.
Longevity: low-leak NBR or PU seals, precision-honed cylinders, hardened rods; typical life ≥ 40,000 cycles.
Low noise: guidance system minimizes chatter for quiet studios and hotel gyms.
Corrosion protection: powder-coated steel standard; SS304 or SS316 recommended for high humidity or poolside areas.
Easy fit: ball sockets or eyelets for 8–10 mm studs with clip retainers for quick service.
Temperature range: reliable from −30 °C to +80 °C; specialty oils on request.
Compliance: RoHS and REACH compatible oils and finishes.
Specifications
Extended lengths: 8 in, 10 in, 12 in, 14 in, 16 in, 18 in, 20 in, 22 in
Typical strokes: 60–200 mm by length
Forces: 120 N, 180 N, 250 N, 350 N, 450 N, 550 N (higher on request)
Cylinder and rod: Ø18ר8 mm or Ø22ר10 mm; heavy-duty options available
Finishes: matte black with QPQ nitrided rod, or polished stainless
End fittings: 8 or 10 mm ball sockets, metal eyelets, angle brackets, quick-release ends
Orientation: install rod end down in the closed position for optimal seal lubrication
How to Choose
Measure length: with the cover open, measure center-to-center between mounts; select an extended length close to this value.
Pick force per unit:
Light plastic console lid: 120–200 N
Medium shroud or service panel: 250–400 N
Large metal cover or added display mass: 450–550 N
Use two supports on wide lids to prevent racking and reduce hinge load.
Environment: choose SS304 or SS316 for high humidity, sweat, or pool adjacency.
Hardware match: confirm stud size (8 or 10 mm) and preferred end fitting type before ordering.
Installation Guide
Support the cover safely.
Lift the retaining clip slightly, press the socket fully onto the stud, then reseat the clip.
Cycle open and close to verify full travel, no interference, and proper damping.
For adjustable-force models, bleed force slowly until the cover settles without bounce and remains open at the desired angle.
Fitness and Gym Equipment
- Treadmill consoles and motor shrouds: controlled lift for service access and safe descent.
- Elliptical and stepper panels: steady hold-open for electronics inspection.
- Indoor bikes and spin consoles: gentle motion for plastic hoods and display covers.
- Rowers and ski trainers: assistance for vertical console or housing panels.
- Strength machines: weight stack guards, selectorized machine doors, cable machine access lids.
- Benches and racks: storage compartment lids and accessory hatches.
Across these use cases, specifiers may call them gas springs, gas struts, lift supports, gas shocks, gas props, or motion dampers-all referring to the same Land-engineered solution for safe, quiet, and reliable console and cover motion control.
Need a matched set for your treadmill line or club fleet? Share length, stroke, cover weight, stud size, and environment. Land will recommend forces, mounting centers, and end fittings, and provide OEM samples with your logo and packaging.
Hot Tags: equipment cover and console lift supports, China equipment cover and console lift supports manufacturers, suppliers, factory, front cab lift gas springs, Yacht Boat Lid Gas Springs, gas rams for access panels, medical cart lift gas springs, nitrogen gas springs for examination lights, hydraulic dampers for recliners


