Overview
Purpose-built for fitness equipment, these compact motion control units-often called gas springs, gas struts, lift supports, gas shocks, gas props, or motion dampers-balance lever arms and seat or backrest pads so athletes can fine-tune positions without sudden drop or rebound. Land engineers each assembly for quiet operation, consistent force, and thousands of gym cycles.
Key Features
Effortless positioning: tuned oil damping provides soft start, smooth travel, and controlled settling.
Size coverage: extended lengths 6–18 inch with typical strokes 30–150 mm for short-throw arms and pad linkages.
Force options: factory-set 80–400 N (≈ 18–90 lbf); adjustable-force versions available for perfect balance.
Hold at angle: internal valving maintains position under vibration and repeated micro-adjustments.
Low noise: guidance system minimizes chatter for quiet studios, hotels, and rehab centers.
Built to last: precision-honed tubes, hardened rods, NBR or PU seal packs; typical service life ≥ 40,000 cycles.
Corrosion protection: powder-coated steel standard; SS304 or SS316 recommended for poolside or high-humidity areas.
Easy install: ball sockets or eyelets for 8–10 mm studs with secure clip retainers.
Operating range: reliable from −30 °C to +80 °C; specialty oils on request.
Compliance: RoHS and REACH compatible oils and finishes.
Specifications
Extended lengths: 6 in, 8 in, 10 in, 12 in, 14 in, 16 in, 18 in
Typical strokes: 30–150 mm by length
Forces: 80 N, 120 N, 160 N, 200 N, 250 N, 300 N, 350 N, 400 N
Cylinder and rod: Ø15ר6 mm or Ø18ר8 mm; heavy-duty Ø22ר10 mm available
Finishes: matte black with QPQ nitrided rod, or polished stainless
End fittings: 8 or 10 mm ball sockets, metal eyelets, clevises, angle brackets
Orientation: install rod end down in the rest position to keep seals lubricated
How to Choose
Measure geometry: with the arm or pad in its working position, measure center-to-center between mounts; choose an extended length close to that value.
Select force per unit:
Light foam pad or short lever: 80–150 N
Standard selectorized arm or backrest: 160–250 N
Long lever or heavy upholstery: 300–400 N
Use two supports for wide pads or asymmetric linkages to prevent racking.
Cycle feel: choose oil-damped versions for softer approach and reduced rebound near the end of travel.
Environment: specify SS304/SS316 for high humidity, sweat, or chlorine exposure.
Hardware match: confirm stud size (8 or 10 mm) and preferred end fitting before ordering.
Installation Guide
Support the arm or pad safely.
Lift the retaining clip slightly, press the socket onto the stud, and reseat the clip.
Cycle through full travel to verify clearance, end-stop contact, and damping quality.
For adjustable-force models, bleed force in small steps until the component stays at the desired angle without drift.
Fitness and Gym Equipment
- Adjustable pads: incline/decline bench backrests and seat pans with easy one-hand positioning.
- Strength machine arms: preacher curl supports, chest press levers, shoulder press and row arms.
- Cable and functional trainers: accessory boom arms and stabilizer links requiring balanced motion.
- Cardio consoles and monitor booms: smooth, secure placement for screens and control pods.
- Rehab and boutique studios: fine control for therapy benches and specialty apparatus.
Across these applications the same components may be specified as gas springs, gas struts, lift supports, gas shocks, gas props, or motion dampers-each referring to Land's engineered solution for safe, quiet, and reliable arm and pad positioning.
Hot Tags: machine arm and pad positioning gas springs, China machine arm and pad positioning gas springs manufacturers, suppliers, factory, Rear Hatch Lift Supports Liftgate Gas Struts, marine gas springs, elliptical machine gas shocks, control cabinet gas struts, display mount gas spring, hydraulic dampers for ottoman lid


